Join 100,000+ CNC'ers! Get our latest blog posts delivered straight to your email inbox once a week for free. The machine knows whether to view a stop as a Home or Limit based on whether it was commanded to home or not, as well as based on what direction it was travelling when it hit a stop and on which circuit (axis) it got the stop signal.īack to CNC Lathe Home… Like what you read on CNCCookbook? This way we will only use 2 inputs from the GRex for the Home/Limit system. I will be mounting the optical limit switches on the apron and mounting stop blocks on the lathe bed (X left and X right) and on the cross slide (Z in and Z out). So, we want to set the machine home positions to be the extreme positive for both axes–far right and far out (cool!). X is left (-) and right (+), Z is in(-) and out (+). We will use 1 circuit for each axis–X and Z. Use a little heat shrink tubing to ensure there are no shorts among the leads.įor the lathe, I want 2 limit switches and 2 circuits.

Just cut one connector off, strip the wires, and solder to the optical switch. You can buy already made up CAT5 cables in various lengths. It’s the same stuff you use to make LAN connections. The optical switch takes 4 leads, so I’m planning to use CAT5 cable. Start with a piece of pre-finished steel rod, cut to length. Drill and tap the setscrew holes on either side of the gate.ġ. Start with a piece of 1/4″ thick aluminum plate.Ĥ. Drill and countersink the holes for the bolts that hold the lid in place.ġ. Drill the side holes that the push arm will ride in.Ĥ. Square it with a flycutter on all sides.ģ. Start with a piece of 5/8″ aluminum plate.

Drill and tap the holes for the bolts that hold the lid in place.ġ. Drill a hole underneath the optical switch for the leads, and drill a connecting hole from the bottom for the wiring to come in and out.Ħ. Drill and tap the optical switch mounting holes.ĥ. Bore the cavity that the optical switch sits in.Ĥ.

One could also use a slitting saw to cut the large amount of stock to be removed over the mounting bracket and then clean it up with a light milling pass.ģ. Probably chain drill those slots with a 1/4″ drill bit and then take a smaller mill to smooth out the edges. Mill down the bottom side of the lid until it is 0.25″ thick and cut the slots for the mounting bolts. Square it with a flycutter on all sides.Ģ. Start with a piece of 5/8″ thick aluminum plate. Do I want to make the base taller and go with a thin lid? I chose this design because my switch (the blue thing) stands up pretty tall and I was looking to machine the top and bottom out of something readily available and easily machined–in this case 5/8″ aluminum.ġ. The limit is tripped when the gate uncovers the optical beam… A bracket is placed on the moving part of the machine that will press against the plunger, open the gate, and enable the beam when the limit is hit: The switch is mounted rigidly via the holes at the bottom. Note plungers on either side–it works 2 ways… The arm has a spring on either side to center it and goes through a hole on either side of the lid: Optical Switch (Blue), Sliding Gate (Purple), Arm (Green)… Now picture a little gate that interrupts the beam inside the optical switch. Mach 3 can take care of whatever polarity (normally open or normally closed) we want to have trip the limit. Because of this, we simply arrange to block the beam (thereby closing the switch) until the limit is hit, which unblocks the beam and opens the switch. We want a limit to behave in normally closed fashion, so that the limit is tripped if a wire is broken. I got a bag of 100 of these slotted optical switches on eBay for almost nothing. Optical Limit Switch for CNC Machines The Design

Optical isolator for raspberry pi 3